-- *****************************************************************
-- CISCO-CABLE-WIDEBAND-CAPABILITY.my: CISCO-CABLE-WIDEBAND-MIB.my
-- AGENT-CAPABILITIES
--
-- July 2006, Wasim Mohammad
--
-- Copyright (c) 2006 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-CABLE-WIDEBAND-CAPABILITY DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,Unsigned32FROM SNMPv2-SMI
AGENT-CAPABILITIESFROM SNMPv2-CONF
StorageTypeFROM SNMPv2-TC
InetAddressTypeFROM INET-ADDRESS-MIB
ciscoAgentCapability
FROM CISCO-SMI;
ciscoCableWidebandCapability MODULE-IDENTITYLAST-UPDATED"200609070000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: Cisco Systems
170 West Tasman Drive
San Jose, CA 95134
U.S.A.
Phone: +1 800 553-NETS
E-mail: cs-ubr@cisco.com"DESCRIPTION"Agent capabilities for CISCO-CABLE-WIDEBAND-MIB"REVISION"200609070000Z"DESCRIPTION"This is the Initial version"::={ ciscoAgentCapability 520}ciscoCableWidebandCapabilityV12R00 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS 12.3BC"STATUScurrentDESCRIPTION"Cisco Cable Wideband MIB capabilities."
SUPPORTS CISCO-CABLE-WIDEBAND-MIB
INCLUDES{ ccwbWidebandObjGroup }VARIATION ccwbRFChannelStorageType
SYNTAXStorageType{
volatile(2)}DESCRIPTION"Only storage type 'volatile' is supported."VARIATION ccwbRFChanQamTos
ACCESSnot-implementedDESCRIPTION"This object is not supported"VARIATION ccwbRFChanQamVlanId
ACCESSnot-implementedDESCRIPTION"This object is not supported"VARIATION ccwbRFChanQamPriorityBits
ACCESSnot-implementedDESCRIPTION"This object is not supported"
VARIATION ccwbWBtoNBRowStatus
ACCESSread-onlyDESCRIPTION"read-only is implemented"VARIATION ccwbWBtoNBStorageType
SYNTAXStorageType{
volatile(2)}ACCESSread-onlyDESCRIPTION"Only storage type 'volatile' is
supported. Write/Create is not implemented"VARIATION ccwbWBtoRFStorageType
SYNTAXStorageType{
volatile(2)}DESCRIPTION"Only storage type 'volatile' is supported."VARIATION ccwbWBtoRFRowStatus
SYNTAXINTEGER{
active(1),
createAndGo(4),
destroy(6)}DESCRIPTION"Only enumerations active(1), createAndGo(4) and destroy(6)
are supported."VARIATION ccwbFiberNodeDescription
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbFiberNodeDescrStorageType
SYNTAXStorageType{
volatile(2)}ACCESSread-onlyDESCRIPTION"Only storage type 'volatile' is
supported. Write/Create is not implemented"VARIATION ccwbFiberNodeDescrRowStatus
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbFiberNodeNBIfIndx
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbFiberNodeWBContlrPhyIndx
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbFiberNodeWBRFPort
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbFiberNodeStorageType
SYNTAXStorageType{
volatile(2)
}ACCESSread-onlyDESCRIPTION"Only storage type 'volatile' is
supported. Write/Create is not implemented"VARIATION ccwbFiberNodeRowStatus
ACCESSread-onlyDESCRIPTION"Write/Create is not implemented"VARIATION ccwbRFChannelFrequency
SYNTAXUnsigned32(55000000..858000000)DESCRIPTION"A range of 54MHz to 860MHz is appropriate for a cable
plant using a North American Sub-Split channel plan.
The spectrum range has been expanded to accommodate
a lower edge of 47MHz and an upper edge of 862MHz
for some European channel plans."VARIATION ccwbRFChannelWidth
ACCESSread-onlyDESCRIPTION
"Write/Create is not implemented.The value of 6 MHz
is appropriate for cable plants running under
NTSC (National Television Standards Committee) standards.
The value of 8 MHz is appropriate for cable plants
running under ETSI standards."VARIATION ccwbRFChannelRowStatus
SYNTAXINTEGER{
active(1),
createAndGo(4),
destroy(6)}DESCRIPTION"Only enumerations active(1), createAndGo(4) and destroy(6)
are supported."VARIATION ccwbRFChannelAnnex
ACCESSread-createDESCRIPTION"The value of this object must be same for all
RF channels."VARIATION ccwbRFChannelModulation
DESCRIPTION"Currently the value of this object must be the same for
all RF channels."VARIATION ccwbRFChanQamIPAddressType
SYNTAXInetAddressType{
ipv4(1)}DESCRIPTION"Only Internet address type 'ipv4' is supported."VARIATION ccwbWBCmStatusValue
ACCESSread-onlyDESCRIPTION"Current WB Cable Modem connectivity state, as specified
in the RF Interface Specification. Returned status
information is the WCM status as assumed by the WCMTS"::={ ciscoCableWidebandCapability 1}END